UAS Smokeeter SE 24 Spécifications

ELECTRONIC AIR CLEANERSINSTALLATION AND OPERATION MANUALMODEL SE 30MODEL SE 40MODEL SE 50

8VIl. PERIODIC MAINTENANCE ANDTROUBLESHOOTINGThe following sections are for the use of trainedservice personnel only.WARNING — THE FOLLOWING PROCEDURE

9• Output reading without the componentsshould read 10 to 12 KV DC positive.3. To measure the collection cell output voltage,place the probe’s tip on

10CHECKING MOTOR CAPACITOR (SE 40 & SE 50)(Refer to Figure 9)The motor capacitor located on the side of the blower isdesigned to start and run the

11TROUBLESHOOTING TABLE*PROBLEM POSSIBLE CAUSE CORRECTIVE ACTIONA. Control switch on, 1. Defective lamp. 1. Replace lamp.indicator lamp off, 2. Faulty

12SE 30 FINAL ASSEMBLY02-2620IX. ILLUSTRATED PARTS

13SE 30 FINAL ASSEMBLY02-2620ITEM PART NO.NO. DESCRIPTION QUANTITY1 02-0090 IONIZER ASSEMBLY+ 12 02-0522 COLLECTION CELL+ 13 20-2922 CORD-IEC, 90 DEG.

14SE 30 IONIZER ASSEMBLY02-0090ITEM PART NO.NO. DESCRIPTION QUANTITY1 10-0421 END PLATE 22 10-0367 CORNER CHANNEL 23 10-0368 SUPPORT 24 37-0004 INSULA

15SE 30 COLLECTION CELL ASSEMBLY02-0522ITEM PART NO.NO.DESCRIPTION QUANTITY1 10-0348 END PLATE 22 10-0158 CELL PLATE, HOT 103 10-0157 CELL PLATE, GROU

16SE 30 CENTER POST ASSEMBLY02-2608ITEM PART NO.NO. DESCRIPTION QUANTITY1 10-2708 CENTER POST 12 02-1326 SPEED CONTROL ASSEMBLY 13 20-0229 PILOT LIGHT

17SE 30 MOTOR/BLOWER ASSEMBLY02-2662ITEM PART NO.NO. DESCRIPTION QUANTITY3 20-0323 WIRE TERMINAL 24 22-0176 MOTOR, 115/1/50-60 16 30-0049 WASHER-FLAT,

18SE 40 FINAL ASSEMBLY02-2724

19SE 40 FINAL ASSEMBLY02-2724ITEM PART NO.NO. DESCRIPTION QUANTITY1 10-2820 MOTOR/BLOWER ACCESS DOOR (WG) 12 10-2821 COMPONENT ACCESS DOOR (WG) 13 02-

20SE 40 UNICELL ASSEMBLY02-1321

21SE 40 UNICELL ASSEMBLY02-1321ITEM PART NO.NO. DESCRIPTION QUANTITY1 35-0067 CELL SPACER 1562 35-0175 CELL ROD 83 10-1373 AIR FOIL CORNER CHANNEL 14

22SE 40 MOTOR/BLOWER ASSEMBLY02-2544ITEM PART NO.NO. DESCRIPTION QUANTITY1 32-0083 BLOWER — DIRECT DRIVE 12 02-1327 MOTOR 13 20-0569 CAPACITOR 14 20-1

23SE 40 CENTER POST ASSEMBLY02-2725ITEM PART NO.NO. DESCRIPTION QUANTITY1 10-2825 EXTRUSION, CENTER POST 12 02-1326 SWITCH — CONTROL VARIABLE SPEED 13

24SE 50 FINAL ASSEMBLY02-2726

25SE 50 FINAL ASSEMBLY02-2726ITEM PART NO.NO. DESCRIPTION QUANTITY1 18-0800 CABINET WELDMENT 12 10-2823 COMPONENT ACCESS DOOR 13 10-2822 BLOWER ACCESS

26SE 50 IONIZER ASSEMBLY/AIRFOIL IONIZER02-0089ITEM PART NO.PART NO. DESCRIPTION QUANTITY1 30-00301/4-20 LOCK NUT 42 30-00491/4” FLAT WASHER 43 35-002

27SE 50 CELL ASSEMBLY/CP COLLECTION CELL02-0086ITEM PART NO.NO. DESCRIPTION QUANTITY1 30-00301/4-20 LOCK NUT 162 37-0008 INSULATOR 83-A 10-0564 HANDLE

1SPECIFICATIONSPOWER REQUIREMENTS115 VAC, 60 HZ3.2 Amps (max.)POWER CONSUMPTION370 Watts (max.)AIR HANDLING CAPACITY MODEL SE 30Low - 150 to 420 CFM*W

28SE 50 CENTER/POST ASSEMBLY02-2727ITEM PART NO.NO. DESCRIPTION QUANTITY1 10-2826 EXTRUSION, CENTER POST 12 02-1326 SWITCH — CONTROL VARIABLE SPEED 13

29SE 50 MOTOR/BLOWER ASSEMBLY02-2576ITEM PART NO.NO. DESCRIPTION QUANTITY1 32-0085 BLOWER — DIRECT DRIVE 10-10 12 02-1357 MOTOR 13 20-0569 CAPACITOR 1

30WIRING DIAGRAMMODEL SE 3041-2487WIRING DIAGRAMMODEL SE 40MODEL SE 5041-2488

4440 Creek Road • Cincinnati, Ohio 45242 USANational Phone: (800) 252-4647Telephone: (513) 891-0400 • Fax: (513) 891-4882http://www.uasinc.comAn ISO 9

2DIMENSIONSSE 30SE 40SE 50201⁄4"51 cm107⁄8"28 cm31"79 cm40"102 cm21"53 cm127⁄8"33 cm20"51 cm191⁄2"50 cm40"

3TABLE OF CONTENTSSECTION PAGEI. Introduction 4II. Inspection of Equipment 4Ill. How Your Air Cleaner Operates 4IV. Installation 4V. Operation 6VI. Cl

COMPONENTS THAT MAKE IT WORKPREFILTER traps the larger particles and evenly distributesthe air across the ionizing section to maximize efficiency.IONI

SE 3075 lbs.5WALL MOUNTINGLevel and securely attach the mounting cleat to thewall, ensuring given dimension from ceiling to boltcenterline as shown in

6SUSPENSIONThreaded rod, wire or eyebolts and chain may be usedfor hanging the unit. Four “knockouts,” located asshown in Figure 4, must be removed.I

7CLEANINGMajor cleaning is confined to the prefilter, ionizer,collection cell and the inside cabinet. These should becleaned periodically to assure c